blemishes

Category B	Version 3.0

Description

This program generates BLEMISH files which mask bad pixels in individual or multiple images.

This procedure creates a blemish (.BLM) file for an image that lives in the BLEMISHES subdirectory.

Required Files

BLEMISHES/ - Directory containing BLEMISH files for individual images and BLEMISH templates for multiple affected images.

IMAGEFILES/ - Directory containing the .DAT file for the image; this program displays the image with masking for user inspection, and reads the Digital Number (DN) of pixels of interest.

SUMFILES/ - Directory containing the SUMFILE for the image to mask; this program reads NPX (number of pixels), and NLN (number of lines);

INIT_LITHOS.TXT - this program reads the parameter BLEMISH (if it exists), which references any existing template for masking bad pixels common to multiple images.

BLEMISHES/TEMPLATENAME .BLM - template BLEMISH file for each INIT_LITHOS BLEMISH entry.

OptionalFiles

BLEMISH/PICNM .BLM - Existing image BLEMISH file for deletion or editing.

Output Files

TEMPFILE.pgm - Display of the image with masking applied.

BLEMISHES/PICNAME .BLM - Generated or edited BLEMISH (.BLM) file.

User Warnings

/!\If the PICNM used to make the original blemish file is not consistent with the template, the program will say so and it will STOP. Otherwise, it will create the template file and, if necessary, remind you to define it in INIT_LITHOS.TXT.

Using blemishes

Initial Inputs

Input 12-character picture nameP00045000455 gc TEMPFILE.pgm b. Block s. Spot q. Quit

Choose the option for the type of blemish you want to work with:

The b. Block option masks a square block of the image specified by a minimum and maximum pixel and line. This type of blemish is typically used for missing or hashy lines due to downlink errors.

The s. Spot option masks a small region around a pixel/line center (p,l) from p-k to p+k and l-k to l+k. An additional input is a brightness threshold (Note: See below for threshold information). If you enter this as zero, everything in the spot will be masked. However, if there is a bright blemish such as a cosmic ray hit in the spot, you can set the threshold to remove only the affected pixels. In this case, you can specify a large region (large k) and all the bright blemishes in that region will be masked without affecting the rest of the data.

Here is a sample TEMPFILE.pgm image before masking is applied:

Figure 00: Image Prior to Applying Mask

Block Blemish Options

Input pxmn, pxmx, lnmn, lnmx512 612 250 350 gc TEMPFILE.pgm b. Block s. Spot q. Quit

After you choose b. Block you must specify:

pxmn, pxmx: must be in the range [1:NPX] (where NPX is the number of pixels in image)

lnmn, lnmx: must be in the range [1:NLN] (where NLN is the number of lines in image)

This sample shows the image after block masking was applied:

Figure 00: Image after Applying Blemish Mask

Spot Blemish Options

Input bad px/ln center, half-size. threshold.512 250 25 100 gc TEMPFILE.pgm b. Block s. Spot q. Quit

After you choose s. Spot you must specify:

px/ln center: Vector with element values in the range ([1:NPX],[1:NLN]) (where NPX is the number of pixels in image, NLN is the number of lines in image)

half-size: Half-size of masked area in pixels, e.g. a half-size of 2 will result in a masked area of 4 pixels x 4 pixels.

threshold: Digital Number (DN) representing the lowest threshold for brightness in the range, where 0 is dark, and will result in all brightnesses being masked. Note: The DN within BLEMISHES has been rescaled by 255/(Brightness DN). So if the original DN is 398 and the max is 1410, then the new DN will be 71 because the number is truncated. So if you want to mask 398, you need to enter 70 for the threshold.

This sample shows the image with spot masking and DN threshold applied:

Figure 00: Image Displaying Blemish Mask Options

Quit Blemishes Option

Save blemish file? (y/n)y Create/change template file? (y/n)n

After you choose q. Quit you must specify whether to save the blemish file and whether to create or change a template file.

BLEMISH Templates

In the event that a camera has bad pixels common to all images, you can create a template that masks these pixels in all that camera's images. The template is specified in the INIT_LITHOS.TXT file with the key word BLEMISH.

For example, DAWN has two framing cameras with image names starting with FC1 and FC2. FC2 images all have several blemishes in the same places. A template in INIT_LITHOS specified by BLEMISH='FC2#########' will correct all of these images without having thousands of individual blemish files. If an image contains additional blemishes it can have its own file with just those additional blemishes.

In order to create a TEMPLATE, you must create a blemish file for one of the affected images with only the common bad areas masked. The procedure will ask: 'Save blemish file? (y/n)' and then 'Create/change template file? (y/n)'. If you enter 'y' and 'y', you will be asked for a 12 character template name with the common characters of the image names in their proper positions and # everywhere else.

/!\If the PICNM used to make the original blemish file is not consistent with the template, the program will say so and it will STOP. Otherwise, it will create the template file and, if necessary, remind you to define it in INIT_LITHOS.TXT.

The following samples show this sequence of actions and the output file:

Save blemish file? (y/n)y Create/change template file? (y/n)y Input 12 character templateP00045###### Add: BLEMISH='P00045######' to INIT_LITHOS.TXT

Example P00045######.BLM file:

488 225 489 225 490 225etc... 534 275 535 275 536 275 537 275END

The BLEMISH file contains a list of pixel/line locations to be masked, appended with the end-of-file identifier, 'END'.

(Compiled by DL) (Updated by JRW)

Based on SPOC v3.02A PDF/LITHOSPHERE/blemishes.f File Reference.

CategoryPrograms