Differences between revisions 1 and 8 (spanning 7 versions)

Block 13 - BuildShape V2

Description

Steps to build, review and install a shape model

Procedure

Set-up

Bob uses a copy/paste technique that is normally held in a support file densify-cut paste. I've created a script in /opt/local/spc/bin called buildShape.sh <version> that will do the same thing in batch. It also runs view_shape to make the 8 views of the object for easy evaluation.

To make the script easier, set this variable

ID=farV03
echo "Building the shape with suffix $ID" >> notes

Running

This is a script in /opt/local/spc/bin that will dumb down a model, then build it back up using maplets.

```
buildShape.sh $ID
```

When this is done, you will have

dum-far320v1
shape-far320v1-64
shape-far320v1-128
shape-far320v1-256
shape-far320v1-512
shape.log -- A log file that saves the commands and output

Evaluate Final Results

Check to see if the offset of the centroid from the center of the system is less than the required criteria (suggest 1/2 image pixel).

echo SHAPEFILES/shape-$ID-512 | shape_info | tee -a ../notes

Install Shape

If you like the results, you can instal the model. Review the red/blue or side-by-side images to ensure the model is good. If it isn't then uninstall the model.

cd SHAPEFILES
relink.sh shape-$ID-512 SHAPE.TXT | tee -a ../notes
cd ..
evalReg.sh lsupport/theEight

Finish the Block

Once that is done, you should iterate on it at least once and rebuild the shape (go back to the top of this procedure until the shift is less than the criteria.

```
echo 9 | blockFinish far\
```

(Compiled by EEP)

-  ⇤ ← Revision 1 as of 2018-11-20 11:15:37 → 
  Size: 1493
  Editor: EricPalmer
  Comment:
+   ← Revision 8 as of 2018-11-20 17:21:00 → ⇥
  Size: 1785
  Editor: EricPalmer
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 15:
+To make the script easier, set this variable
-Line 16:
+Line 17:
-   buildShape.sh farV01
+ID=farV03
echo "Building the shape with suffix $ID" >> notes
-Line 18:
+Line 20:
+=== Running ===
This is a script in /opt/local/spc/bin that will dumb down a model, then build it back up using maplets.

   {{{
buildShape.sh $ID
   }}}
-Line 25:
+Line 34:
- * shape.log.  A log file that saves the commands and output
+ * shape.log --  A log file that saves the commands and output


=== Evaluate Final Results ===

Check to see if the offset of the centroid from the center of the system is less than the required criteria (suggest 1/2 image pixel).

   {{{
echo SHAPEFILES/shape-$ID-512 | shape_info | tee -a ../notes
   }}}



=== Install Shape ===
If you like the results, you can instal the model.  Review the red/blue or side-by-side images to ensure the model is good.  If it isn't then uninstall the model.

   {{{
cd SHAPEFILES
relink.sh shape-$ID-512 SHAPE.TXT | tee -a ../notes
cd ..
evalReg.sh lsupport/theEight
   }}}




=== Finish the Block ===
Once that is done, you should iterate on it at least once and rebuild the shape (go back to the top of this procedure until the shift is less than the criteria.

   {{{
echo 9 | blockFinish far\
   }}}
-Line 32:
+Line 72:
-=== Evaluate Final Results ===

Check to see if the offset of the centroid from the center of the system is less than the required criteria (suggest 1/2 image pixel).

{{{
   shape_info
     shape-far320v1-128
}}}

If you need to shift it, run the [[shift]] command
{{{
   shift
   -OffsetX -OffsetY -OffsetZ
   y
   shape-far320v1-128
   n
   y

   geometry
   20
   1
   n
   n
}}}


Once that is done, you should iterate on it at least once and rebuild the shape (go back to the top of this procedure until the shift is less than the criteria.





=== Install Shape ===
{{{
   relink shape-far320-128 SHAPE.TXT
   evalReg.sh lsupport/theEight
}}}





=== Finish the Block ===
{{{
  echo 8 | blockFinish far\
}}}